ALITEC CORPORATION (Pavement Services) is the U.S. industry leader in manufacturing Skid Steer Power Attachments: Cold Planers, Boom-Mounted Cold Planers, Rock Wheels, Tillers, Flail Mowers, Vibratory Rollers, Low Flow Planers, Augers, Stump Grinders and Hydraulic Breakers.

Pavement Services MG690 Maintainer is without competition in providing total job site preparation. From initial ground breaking to final grading, compaction and clean-up, the MG690 Maintainer gets the job done with cost-saving efficiency.

Pavement Services' Model MG747 articulated motor grader offers the features and benefits of much more expensive graders: frame hydraulically articulates 27 degrees; dual oscillating rear tandem wheels; full floating front axle with 10 degree wheel lean; 10 ft (3.05 m) mold board features a 36 inch (914 mm) sideshift and 45 degree angle capability; adjustable, tilting operator console; 4 cylinder engine produces 60 HP (44.7 kw) at 3000 RPM; 4 speed transmission provides speeds to 20 MPH (32 KPH); optional front mounted 7 ft. (2134 mm) blade and rear scarifier available.

Alitec Skid Steer Cold Planers:

Models: CP16ATD, CP20ATD, CP24ATD and CP30ATD

Top pivot design self levels the drum and chassis creating higher downforces, precise depth control and easier operation. Wheels on the drum chassis minimize the changes of gouging the asphalt. Side skids reduce the possibility of the wheels dropping into the cut when milling potholes or making butt joints. Electrohydraulic tilt depth and sideshift control eliminate difficult manual adjustments and is standard on all models.

• For 1300 lbs (550 kg) and larger skid steers
• Top pivot drum design
• Planetary drum drive efficiently mills asphalt or concrete
• Widths from 16in - 30in (400mm - 762mm)
• depths to 6in (0-150mm)
• Electro-hydraulic tilt, depth and sideshift control

Alitec Skid Steer Boom-Mounted Cold Planers:

Your backhoe or excavator becomes a powerful cost effective milling machine with the addition of an Alitec cold planer.

Features
• Double reduction planetary drive
• Available in widths from 16 to 36" (400 to 915mm)
• Powered by machine's auxiliary hydraulics

Alitec Skid Steer Low Flow Planers:

Model CP12LF

Features
• Operates on standard hydraulics (11-20 gpm, 42-75 lpm)
• cuts 12" (305 mm) wide
• Hydraulic sideshift (22", 560 mm)
• Manual Tilt (+/- 19º)
• Manual depth adjustment (0-5", 0-125 mm)
• Direct drive high torque drive motor
• 28 pick drum mills concrete or asphalt without high flow hydraulics

Alitec Skid Steer Rock Wheels:

Attach an Alitec Rock Wheel to your skid steer to cut through asphalt, concrete, rebar and frost. makes precise cuts prior to road repair or laying utility lines.

Features
• 40:1 planetary drive
• Hydraulic sideshift and depth control
• Cutting widths of 2.5 or 4.5"/63 or 115mm
• Cutting depths of 12, 18 or 24"/300, 450, or 600 mm

Alitec Skid Steer Tillers:

Break up packed soil or finish till prior to reseeding with the Alitec skid steer tiller.

Features
• Dual direct drive design eliminates the need for any bearings or chains and their maintenance.
• Bi-directional tine rotation allows unit to operate with loader moving forward or backward.
• Dual direct drive design with end port hydraulic motors allows unit to be operated close to obstacles such as fences or buildings.

Alitec Skid Steer Flail Mowers:

Models FM62 and FM74

The Alitec Skid Steer Flail Mower is perfect for site clearing or mowing right-of-ways.

Features
• Forward rotation allows knives to pick up flattened grass and suck in tall grass and weeds.
• Knives fold back on impact with rocks and other debris.
• Belt drive design allows operation near fences and guardrails.

Alitec Skid Steer Vibratory Rollers:

Turn your skid steer into a powerful compactor. Our line of rollers are available in smooth or padfoot drum styles and have compaction forces up to 10,000 lbs. (4500kg.)

Features
• Powered by skid steers standard auxiliary hydraulics
• Drum and shaft bearings lubricated in an oil bath system
• Quick tach compatible with most skid steers
• Available in 48, 66 and 73" widths (1200, 1675 and 1850 mm widths)

Alitec Skid Steer Augers:

Model HA15:
• Drive - Chain
• Required Flow
  • GPM - 10-20
  • LPM - 38-76
• Torque at 2000 PSI (130 Bar) - 1088 ft./lbs.
• Bit Sizes
  • in.- 6-24
  • mm - 152-610

Alitec Skid Steer Stump Grinders:

Model SG40

Turn your skid steer into an effective stump remover. The SG40 attaches in minutes for quick and easy job site clearing.

Features
• Hydraulic swing, raise and lower, extend and retract
• Cuts 21" (530mm) above ground, 16" (400 mm) below ground
• Uses industry standard stump cutting teeth
• All functions controlled from the cab

Alitec Skid Steer Hydraulic Breakers:

Features
• Nitrogen charged backhead for superior impact energy and shock dampering
• Innovative valve design suppresses hydraulic pulsations
• Built-in diaphragm-type accumulator for surge protection and smooth operation
• Replaceable chuck bushings and thrust rings
• Models of 250, 500 and 750 ft./lbs.

Alitec Model MG690 Maintainer:

From initial ground breaking to final grading, compaction and clean-up, the MG690 Maintainer gets the job done with cost-saving efficiency.

Alitec's Maintainer is packed with performance features like all wheel hydrostatic drive, power assisted steering and fingering controls. The full width scarifier has power to spare for breaking up the hardest, most compact soil with any combination of its six teeth. The fully controlled moldboard is equipped with a power sideshift capacity of 3 ft., allowing the blade to reach beyond the wheels to cut handwork around poles and railings. Clean-up of all types of material is easy with the self-leveling front end loader that can also be used as a back blade.

With unprecedented availability of power attachments, the MG690 becomes a highly productive tool carrier. From a moldboard-mounted 40" wide cold planer, to a loader mounted 88" wide flail mower, the MG690 can be the most productive investment in your fleet.

Alitec Model MG747 Motor Grader:

Features
• Frame hydraulically articulates 27º
• Dual oscillating rear tandem wheels
• Full floating front axle with 10º wheel lean
• 1' mold board features 36" sideshift and 45º angle capability
• Adjustable, tilting operator console
• 4 cylinder engine produces 60 hp at 3,000 rpm
• 4 speed transmission provides speeds to 20mph
• Optional front mounted 7' blade and rear scarifier available

Home | About Us | Offices | News | Map | Index | Contact Us

* * * *
Copyright © 2003, Ferrex International, Inc. All rights reserved.